|
Romy the Cat's
personal site dedicated to advanced audio and evolved music reproduction
techniques
|
|
|
|
|
[quote user="floobydust"] Some very good points here... if I downloaded the correct schematic from your site for the 6-channel Melq amp (also has the term DSET in the title) then you have created a 6-channel SET amp with built-in crossover points. Yo...
|
[quote user="MINGSU"]GOTO always recommend to use 1st order active crossover and 2nd order passive crossover. The reason to use 2nd order for passive crossover is to protect the driver. Of course, the user can use whatever they like the best but the ...
|
The rule of thumb is that you can't localise sounds below 80hz. The classic experiment is to use a sub with an adjustable xo point and adjust it untill you can't tell where it's comming from. That doesn't change the fact that seperating the bass into...
|
I had in my basement Marchand X26 crossover that I use over 10 years back. Since my B-2 power amp with passive filter is being fixed I setup the stock fixed B-2 with external Marchand active crossover. I spent some time to modify the Marchand X26 bi...
|
[quote user="speedysteve"]The systems I've heard with steep slopes (only 4th or 8th order) sound hard and unnatural to me.[/quote] Yes, the higher order crossovers do sound harder even if all time alignment measures are taken. Still, do not forget th...
|
IMO A 60Hz attempt is too low and a 120Hz attempt too high. This is a difficult task, that of properly integrating horn loaded mid-bass withD.R subs.What type and slope crossover are you using ?I'm hoping you are going active here ?How much air can ...
|
Hi all!
I am also big horn fan from Latvia.This is my first horn project Prelude.1" high frequency driverCrossover 4000HZ2" midrange driver crossover 500Hz15" midbass crossover 100Hz15" Tapped horn (is not yet complete)Unfortunately midb...
|
[quote user="noviygera"] I think clearing this up this may be of benefit to other users who are building multi-way horns.Let's say I've got two horns mounted on a frame. There's a high horn above and a mid horn below and they are physically time alig...
|
I spoke about the minimum proximity of a crossover point to the horn rate but there was one very fine point that I did not address and that I never have seen voiced. We have a horn and the driver of the horn is properly crossed, far enough to escape ...
|
Ok that was a long road to "stick with vertical alignment, and stay away from BMS." Back to compression drivers, and implementation...
If I were in your shoe I would take make as you wish but wish a slight correction:
65Hz Tractrix fro...
|
[quote user="noviygera"]I have been thinking about how nice it would be to have have a good sounding DSP for crossover and delay functionality. I know this subject was covered here before but what was talked about is this DSP is not that good, and th...
|
[quote user="Romy the Cat"]I am sorry; I do not follow what you are saing. I see no relation between a need to use a crossover with DSET topology. The Cat[/quote]What I am thinking is that with full range amplifier, you must use a speaker level cross...
|
There are a few other ways to roll off HF: shaping and extending front chamber, playing with damping of the driver cone and so in. The Altec 515G at 220H, what the channel above? When you say that you have too much HF then how do you methodologically...
|
So, you use DCX 2496 for deals but not for crossovering and your crossovers are still on analog domain, right? Romy, I do everything in the digital domain so I use DCX 2496 as my crossover as well (but analog SS pro amps). I know you're no big fan of...
|
[quote user="jessie.dazzle"] Though the frames have wheels and roll very easily, my room is cursed with an elevated platform smack in the middle of everything (about 14 inches higher than the main floor), and to move the horns up on to or down off of...
|
In the past month I have been playing around with a sub-woofer. This is my first experience with a sub. Prior to this, I held a bias that subs generally cause more problems than they solve. I am using a sub now because the main horn...
|
[quote user="cv"] I bet Yamamura is using non-causal filtering... this is all running off a music server, so could process everything offline. [/quote] Chris, there is no such a thing as “non-causal filtering”. Filtering is filtering, would it d...
|
waveguides as far as i can tell are designed to equalize the power response.
for example if we are talking about a typical 2-way speaker with a 7" midbass and 1" tweeter then there will be a discontinuity in the power response around the crossover...
|
[quote user="jessie.dazzle"]I've been listening for about one week now with the filters set so the hand off from lower-mid to upper-mid happens higher up (upper-mid S2 is high-passed at 4800Hz instead of 3200Hz), meaning the small 400Hz horn is doing...
|
[quote user="Bill"]
Had problems 2 and 3 here with my British crossovers
Both speakers have the 78 hz. Dip after a 50 hz. Peak. they are probably room resonances. Try moving the speakers and/ or the mike and remeasure.Also you have the sa...
|
I want to share what I feel is a good application of an injection channel, as introduced by Romy. But this is different and also useful and i can tell you it works and very well. Of course, I do not recommend to use this application in the same exact...
|
Jessie, in the configurations of the horns and derivers that you are building your mid channels do not exposed too much to stresses. It is not that you have a situation when 1/4 octave more and less will send your channels into suffocation - your hor...
|
and this is the huge decision.. although Steve and Rich's drivers do have the potential for extremely wide bandwidth, I feel that the first decision when designing a horn speaker is to decide how many horns and the corresponding crossover points...
|
[quote user="ayebee"]I’m probably suggesting the obvious, but have you tried adjusting the crossover component values on the fundamentals and MF-channels? On the fundamentals-channel, increasing the inductor-value, and decreasing the cap, so that...
|
Hi All,This is my 1st ever post, but extremely disappointed I never came across this site beforeHere is my current setup, for which I'm desperately seeking some help from fellow membersCabinet - Layered Birch Ply with curved sidesWoofers [93.67dB]- 2...
|
[quote user="noviygera"] Romy, I have somewhat
different possibilities than you are seeing. My system is physically higher
than most because my listening position is at standing height or sitting in a
high stool. I have used this litening height f...
|
I was reading the Stefano Bertoncello's post about his new multi-amping again options.
http://twogoodears.blogspot.com/2010/09/multi-amping-again.html
.. and I feel that it would be a good idea to brief summarize multi-amping cros...
|
Hans, indeed, generally it
it not a good idea to have idea put crossover point in between 2 and 4K but it
is a general rule. That rule that might be very much overridden by a good
practical implementation of a particular installation. To do this “...
|
[quote user="ulf"] Well, it was not really a surprise to us that the horn without the phase plug was dissapointing. Without the plug we had a horn that was a bit too short, had too large front cavity and less compression than we desired. [/quote]
It...
|
[quote
user="martinshorn"]So what was next...
They build the DAC, patented the clock... ok.
They build their own preamp. Fully descrete class-a balanced,
john curl wouldnt do it differently. Nice. Low and adjustable gain - very nice.
Constant im...
|
|
|
|
All context of this site except the Forum's posts
Copyright © Roman Bessnow 2004-2024
All messages within the Site’s Forum Copyright © by
authors of the posts
|
Last 24-hours posts: |
0 |
|
|
|
Total human visitors: |
42,755,702 |
|
|
|
|
|
|