|
|
| Romy the Cat's
personal site dedicated to advanced audio and evolved music reproduction
techniques
|
|
 |
|
|
|
|
|
As I learned today the Australian Martin seddon know as the Azurahorn Guy has a web site and he also does horns:
http://www.azurahorn.com/azurahorn_tradesecrets.htmlFrom Martin’s site:Azurahorn is best described as a long term audio project, funded ...
|
|
I'd put your sub horns above your head. There are some big issues with that but you save a lot on concrete engineering, and assuming space remains in future you could apply what you learned from the overhead wood horns to a more refined bass setup. O...
|
|
Hi Romy,Its an Altec 416-8A driver in a ~100 Hz exponential horn, Jbl 2441 in 350Hz tractix, Aurum Cantus G1 tweeter and Eminence Definimax 4012 HO in ~30Hz Tapped horn.I just hooked it up and the highs are promising but I thought the lower end (200 ...
|
|
Of course I am not really talking about Rullit but only holding up his implimentations against his stated aims. This is certainly no special case, since most smart people learn the talk and the "look" long before they learn practicum, if they ever d...
|
|
[quote user="Romy the Cat"]I woke up and thinking about the horn problem with fresh head I am thinking what did wrong. I did not measure the frequency response of the horn – I did not see a need for it – the sound of the thing is way beyond where it ...
|
|
It is 4” exit and reportedly goes down to 27Hz. I do not know what a lot about this diver but it might be a good driver for 40Hz horn. 4” into 40hz? God, it has to be at least 16 feet long horn! I would take my head off to somebody who goes for it. A...
|
|
Romy, Looking at your cartoon again, I wonder if you are showing manufactured trusses inside the horns?If not, what does the shading that looks like trusses mean to show?If so, your carpenters are either very good, very optimistic or very hungry.Are ...
|
|
[quote user="jessie.dazzle"]From this and from the mention of 3/4" plywood, I deduce that the "curved" walls of these horns will likely be described by a series of facets (flat planes). It is said to be okay at these frequencies; this must assume a p...
|
|
Romy, thank you for your thoughts. First off, my further thought on the system and specifically the implementation of the high freq section: Yes, the time alignment would be a challenge but possible. This is the main compromise, in my view but the le...
|
|
Romy wrote : Be prepared that the “recommendations” will create more problems then solutions….That should be a disclaimer that all visitors to this site have to sign before reading... I have now spent almost a year trying to tame my Vitavox S2s...
|
|
Hi Romy, I ended up using a TAD 1101h 11 inch driver, 97db, 38fs, and is what I believe a stronger cone than the Goto 8 inch. The DIY mid bass horn is a 1/2 space 53hz hyperbolic horn with 5in x 5in square throat. Length is about 8'6", height of mout...
|
|
Completely understandable. That's why it's fun! It's enjoyable to make something, study the results, make changes, and start over! That seems to definitely be the theme with horns from what you guys are telling me.So it sounds like I shouldn't expe...
|
|
[quote user="Jorge"]Using the Fane 8M is interesting mainly if I get a better sound, Gravitas and size![/quote] Well, the “promised” the gravitas and size but it need to understood that it will not be coming from fane for from extra length of the ho...
|
|
[quote user="Romy the Cat"]
...this interesting point has no practical answer. First of all in the case of Rakesh horn what N-Set proposed is not necessary. Those 115Hz Hasqiun-style horns that Rakesh emulates are well dumped with own mass and own ...
|
|
As I reported at GSC, my CD transport started acting up (skipping) quite a while ago, at a time when I was unable to deal with it. I thought at first I had ruined several CDs by playing them in my car, but that turned out to be a coincidence. When I ...
|
|
[quote user="noviygera"]My mid/upper horns play down to 190Hz. That is -- 188Hz is the Fs of the mid. It's a horn loaded a 10" Precision Device driver. So I need a section (or two sections) to cover the bottom (below 190hz). [/quote]
Herman, i...
|
|
[quote user="scooter"]If you are going to be sanding in your living quarters, I strongly recommend that you:1) cover the ENTIRE rug in the room; you will never get all of the dust out of the rug and will ruin most any home vacuum cleaner (alternative...
|
|
The horns are still plugged but I desired to test if the vibration from the midbass hors will be detectable on the listing room floor. The mouth of the horns does vibrate. Well, it is not a vibration but rather some shaking – pit in this way – if I h...
|
|
Do you even need a horn to run it at 5kHz? The acoustic transformation's probably done by the time the wave reaches the throat. Or is this more just to shape the rolloff below 5kHz? I once tried a hornless S2 as a tweeter; it was quite lovely but did...
|
|
It is depends what kind horn it is. For LF horn the resonance should not be “an octave lower then lowest frequency you can realistically get from the horn”. In fact the common way is to much the assembly resonance to the horn cut off by squashi...
|
|
Allo fellas,
Regarding pricing, best if you check with Martin; I know what I'm paying but I had to commission them specially - I know a hell of a lot of work went into making the mould, jigs to support the mould, etc etc. Actually the 340s were my c...
|
|
Hi there
I can see Romy's face when he's trying to figure out Martin's time alignment strategy;0) I have Martin's 204 Hz horn with Fostex 208 E Sig. These horns are to be big to properly integrate with anything. They are OK with Fostex Lowther drive...
|
|
A visitor of my site, a guy who never ask stupid question about audio, asked me a question how to find a correct size of the back chamber of a straight upper bass horn that he juts built. I wrote a reply but then realized that it would be worth to up...
|
|
Hello BE,Quotes from BE in blue :A tractrix and a exponential horn was compared in a AES paper sometime 1950-1970, I dont remember when exactly.
Does anyone know where I might get a look at this paper?The two round and straight horns where mad...
|
|
KlausMartin (Azura horn ) is making for me extension to 2.75" (BC 8p21)and 1.4" for 204 Hz (altec 288c) .He also developed 550 hz horn for S2 . He understands importance of smooth driver -throat transition . It would be ready to go solution for...
|
|
ygoh wrote:
1.) What's that formula to calculate the back chamber volume given a throat reactance?
2.) Would it be a bigger back chamber with higher reactance at the throat? or vice versa?
You do not ne...
|
|
Hi thereFor some time its bugging me that compression drivers got a very heavy but odd load of air coupling on the membrane. I saw a scatch here to put ideally 2 Horns on each side of the driveway to balance it. That's obviously not so economically :...
|
|
Brass instruments function much differently than audio horns. First of all they are built extremely resonant by mismatching length and horn taper. The taper of the bell is there not for horn type efficiency, rather to change the acoustical length of ...
|
|
Last time we wrote you thought I should focus less on tweeters and more on midbass.I am not done yet, but I have found a very nice midbass solution. Somewhat unorthodox, maybe.I have come to love police sirens! Without having A/B compared it to a pai...
|
|
So, with this horn I got the sound I was dreaming for!Currently system consists of 4 channels:1. RAAL Lazy Ribbon (14k+)2. JBL 2453 in 550Hz LeCleach (1200 - 14k)3. JBL 2490 in first part of own JBL horn (300-1200)4. 12" Supravox in 42Hz 2m long horn...
|
|
|
|
|
All context of this site except the Forum's posts
Copyright © Roman Bessnow 2004-2024
All messages within the Site’s Forum Copyright © by
authors of the posts
|
|
Last 24-hours posts: |
1 |
|
 |
|
|
Total human visitors: |
43,010,703 |
|
|
|
|
|
|